A poorly functioning bathroom drain is a common household problem that can cause complete chaos. A bathtub drain can become worn out, corroded or clogged over time, and you may need to replace or clean it. So, learning how to remove a bathtub drain is a skill you should not neglect. To remove a bathtub drain, follow the instructions given in the article.
Source: Pinterest (Plumbing supply)
Step-by-step guide to help you remove a bathtub drain
Materials required
- Screwdrivers
- Pliers or wrench
- Plumbers’ putty or sealant
- A wire coat hanger or drain snake
Procedure
Identify your drain type and remove the drain cover
There are a variety of drain stoppers available, each using a different mechanism. Read this guide to find the one you are dealing with. Depending upon your drain cover, follow the mentioned steps.
- Push/Pull drain stopper: This drain stopper can be pulled up or pushed down to close or open the drain. To remove it, pull the stopper up and then turn it anticlockwise until it comes off.
- Lift-and-turn drain stopper: This stopper can be lifted up and turned to close or open the drain. To remove it, lift it up and turn it anticlockwise until it unscrews. If the drain has screws, unscrew it to remove it.
- Trip-lever drain stopper: This stopper is operated by a lever on the overflow plate of the tub, just below the faucet. To remove it, unscrew the overflow plate and pull out the hardware that connects the lever to the stopper. Next, pull out the drain stopper from the overflow drain.
- Toe-touch drain stopper: This is a stopper that you can press down with your toe to close or open the drain. To remove it, just unscrew it counterclockwise by hand or with a screwdriver.
- Pop-up drain stopper: Pop-up drain stoppers use the same mechanism as trip-lever drain stoppers. The pop-up drain stoppers are spring-activated to seal the drain.
- Flip-it drain stopper: Flip-it drain stoppers have a toggle on the top that opens and closes the drain. Gently grasp the outer round body, rotate the stopper and pull it upwards at the same time.
Remove the drain basket
The next step after removing the drain cover is to unscrew the drain basket. Use pliers or a tub wrench to unscrew it.
To use the drain wrench, you need to insert it into the drain and align it with the crossbars. Now, turn it counterclockwise until the drain basket loosens. If you are facing problems removing the drain basket, apply some oil to loosen it.
It’s important to use pliers that are large enough to provide a firm grip on the drain basket. To use pliers, insert the jaws of the pliers into the drain basket, ensuring a secure grip. Do not apply excessive force, as it may damage the basket. Turn the pliers anticlockwise and make sure to apply steady pressure while turning and remove the basket.
Clean the drain
Once the drain basket is removed, you need to clean the drain opening and prepare it for the new drain. Use a wire coat hanger or a drain snake to clear the drain. Clean out any accumulated debris or hair from the drain. Be cautious not to damage the drain pipe while doing so. Use a brush or old toothbrush to scrub away any hair, soap scum, or debris that may have accumulated in the drain area. Then, wipe the drain opening with a damp cloth and let it dry.
Inspect and replace if needed
Now, you need to inspect the condition of the drain. If the drain is in good condition, clean it and apply a fresh layer of plumber putty or silicone caulk for a watertight seal. Gently screw the drain back into place, rotating it clockwise.
If there are any signs of corrosion or damage, or if the drain is worn out or in poor condition, it must be replaced. Purchase a suitable replacement and install it according to the manufacturer’s instructions. Use the recommended sealants or plumber’s putty to create a proper seal.
Test for leaks
Last but not least, it is important to check the drain for any leaks. Fill the bathtub with water and let it sit for a few minutes. Check around the drain area for any signs of leaks. If you find any, double-check that all the components are correctly installed and tightened.
FAQs
Can I remove a bathtub drain myself?
Yes, you absolutely can. Removing a bathtub drain is an easy task when done carefully and cautiously.
How do I remove a stuck drain?
If the drain is stuck and won't unscrew, consider using a penetrating oil to loosen it.
Can I reuse the old drain?
Yes, if the drain is in good condition, you can reuse it.
How do I clean the drain before reinstalling it?
Use a mixture of baking soda and vinegar, scrub the drain with a brush and rinse it thoroughly with water.
What is the need to apply a plumber's putty in the drain?
A plumber's putty helps to create a watertight seal between the drain and the tub.
Are there any safety precautions to follow when removing a bathtub drain?
Wear protective gloves and eye goggles and work cautiously.
How often should I remove and clean the bathtub drain?
You should clean the drain at least once a year to prevent clogs and maintain proper drainage.
Are there different methods to remove different types of drains?
The basic steps are the same to remove the drain regardless of the type. You can read the guide to learn about your drain.
Should I hire a professional to remove the bathtub drain?
If you're unsure of the process, it may be best to seek the assistance of a professional plumber.
| Got any questions or point of view on our article? We would love to hear from you. Write to our Editor-in-Chief Jhumur Ghosh at jhumur.ghosh1@housing.com |
